500万彩票

服務熱線: 400-117-8816
           13406879330

500万彩票ZHUANZHUYUNIUJIANXINGDIANDONGBANSHOU、NIUJIANXINGSHOUDONGBANSHOU、DINGNIUJUDIANDONGBANSHOU、NIUJUBEIZENGQIDEYANFAYUSHENGCHAN

熱門關鍵詞: 電動扳手能更快速地完成螺栓鏈接嗎? 重型應用螺栓完成平安快速扭緊和拆卸的處理計劃 工地用的電動扳手哪里有賣的,哪家質量好? 電動扭矩扳手必需恪守的硬性規則500万彩票

當前位置:首頁>新聞中心>定扭矩電動扭矩扳手怎么使用

定扭矩電動扭矩扳手怎么使用

來源:http://29xue.com 日期:2019-04-23 發布人:admin

  定扭矩電動扭矩扳手使用方法:

  Use method of fixed torque electric wrench:
  1、根據工作所需扭矩值要求,確定預置扭矩值。
  1. Determine the preset torque value according to the required torque value.
  2、預置扭矩值時,將六角調節鑰匙插入扳手尾端,然后旋轉,調節標尺刻線至所需扭矩值。調節好后,將鑰匙拉出。
  2. When presetting the torque value, insert the hexagonal adjusting key into the end of the wrench, then rotate and adjust the ruler's marking to the required torque value. After adjusting, pull out the key.
  3、在扳手方榫上裝上相應套筒,并套住緊固件,再在手柄上平穩地施加扭矩至額定扭矩。當擰緊到發出信號“嗒”的一聲(已達到預置扭矩值)止,一次作業完畢。
  3. Install the corresponding sleeve on the square tenon of the wrench, and cover the fastener, then apply the torque to the rated torque smoothly on the handle. When tightened to the signal "click" (reached the preset torque value), one operation is completed.
  力矩扳手選購參數標準
  Standard for Selection and Purchase Parameters of Torque Spanners
  1、手柄人體工程學優化設計,握持舒適,大大降低高強度操作 力矩扳手 時產生的疲勞感。
  1. Optimum design of handle ergonomics, comfortable grip, greatly reducing the fatigue of high-strength operating torque wrench.
  2、雙刻度尺,可精確設定扭矩值。
  2. Double scale, which can accurately set the torque value.
  3、達到設定扭矩值時,發出清晰的報訊聲,并且在手柄上可感覺到輕微震動。
  3. When the set torque value is reached, a clear signal is emitted and a slight vibration can be felt on the handle.
  4、鎖定環靠近虎口處,可避免誤操作改變設定扭矩值。
                                   電動扭矩扳手
  4. Locking ring is close to tiger mouth, which can avoid misoperation and change the set torque value.
  5、扳手長度:990MM。
  5. Spanner length: 990MM.
  6、驅動方尺寸3/4英寸。
  6. Driver size is 3/4 inch.
  7、比較小刻度間隔1。
  7. Minimum scale interval 1.
  8、應用力矩應在扳手的扭力范圍40%至90%之內。
  8. The applied torque should be within 40% to 90% of the wrench's torsion range.
  9、按扭力要求鎖緊螺母。
  9. Lock nuts according to torsion requirement.

上海11选5 上海11选5 上海11选5 江西11选5 江西11选5 江西11选5 3D之家 3D之家