500万彩票

服務熱線: 400-117-8816
           13406879330

ZHUANZHUYUNIUJIANXINGDIANDONGBANSHOU、NIUJIANXINGSHOUDONGBANSHOU、DINGNIUJUDIANDONGBANSHOU、NIUJUBEIZENGQIDEYANFAYUSHENGCHAN

熱門關鍵詞: 電動扳手能更快速地完成螺栓鏈接嗎? 重型應用螺栓完成平安快速扭緊和拆卸的處理計劃 工地用的電動扳手哪里有賣的,哪家質量好? 電動扭矩扳手必需恪守的硬性規則

當前位置:首頁>新聞中心>電動扭矩扳手必需恪守的硬性規則

電動扭矩扳手必需恪守的硬性規則

來源:http://29xue.com 日期:2019-10-14 發布人:admin

  電動扭矩扳手設備精細應用普遍,大家在運用中有很多留意事項,但是只是理解這些留意事項還是不夠的,在運用電動扳手的時分還有些硬性規則是必需要恪守的。

  The fine application of electric torque wrench equipment is widespread. There are many matters needing attention in the operation, but it is not enough to understand these matters. There are some rigid rules that must be abided by when using electric wrench.
  A.電動扳手必需指派專人運用及保管,其別人不得運用。
  A. Electric wrenches must be used and kept by special persons, and no one else can use them.
  B.寄存電動扳手地點要清潔潔凈。
  B. The place where the electric wrench is deposited should be clean and clean.
  C.運用過程中,手要清洗潔凈,不得濕潤。
  C. In the process of application, hands should be clean and not wet.
  D.套筒裝置:檢查套筒的磨損和決裂狀況,確認完好,先將機用套筒上的O型橡膠圈拆下拔出肖軸,再將套筒裝置至四方頭上,裝上肖軸和O形橡膠圈。
電動扭矩扳手
  D. Sleeve device: Check the wear and tear of sleeve and confirm that it is in good condition. First, remove the O-shaped rubber ring from the machine sleeve and pull out the Xiaoshafts. Then, put the sleeve device on the square head and install the Xiaoshafts and O-shaped rubber rings.
  E.每半年對電動扳手停止全面檢修,齒輪注油、軸承注油,漏電檢查、 改換碳刷、清算電機滑環等。
  E. Stop overhauling the electric wrench every six months, gear oil injection, bearing oil injection, leakage inspection, carbon brush replacement, motor slip ring clearance, etc.
  F.裝卸每一螺絲連續沖擊時間不應超越5秒。電動扳手運用辦法,工作五秒后,中止五秒。
  F. The continuous impact time of each screw should not exceed 5 seconds. Electric wrench operation method, five seconds after work, stop five seconds.
  G.運用過程中,牢結實定住工具,確保能長時間穩定站立,中途停用時,電動扳手要放置枯燥地點,不得隨意亂放,不得用電纜搬運、拉動電動扳手。
  G. In the process of using, firmly fix tools to ensure long-term stable standing. When stopping, the electric wrench should be placed in a dull place. It should not be placed randomly. It should not be moved or pulled by cable.
  H.電動扳手運用的機用套筒方頭尺寸應與螺栓的規格分歧。
  H. The size of the square head of the sleeve used in the electric wrench should be different from that of the bolt.
  I.每次運用前和運用后,電工要檢查電刷磨損狀況,當電刷磨損約5mm時,應及時改換兩端電刷。
  I. Before and after each operation, the electrician should check the wear condition of the brush. When the wear of the brush is about 5 mm, the two ends of the brush should be changed in time.
  J.不得隨意將不配套的套筒裝置至電動扳手上。
  J. Do not install incompatible sleeve device on electric wrench at will.
  K.運用完成后要及時撤除電源,對電動扳手停止清算。
  K. After the completion of the operation, the power supply should be removed in time, and the electric wrench should be stopped liquidating.
  L.改動電動扳手轉向時,必需使電機停轉,然后再改動開關轉向。
  L. When changing the steering of electric wrench, it is necessary to stop the motor, and then change the switch steering.
  M.電動扳手所接電源開關必需有漏電維護。接電前檢查電動扳手開關位置,確認在關的位置后在接電源,接電后,電工要對電動扳手及電纜停止漏電檢查,無問題前方可運用。
  M. The power switch connected by the electric wrench must have leakage maintenance. Check the position of the electric wrench switch before power connection, confirm the position closed and connect the power supply after power connection. After power connection, the electrician should check the leakage of the electric wrench and cable to stop. It can be used before there is no problem.
  為了平安起見,以上規則在運用電動扭矩扳手中切不可馬虎大意,務必認真看待,畢竟平安是位的。本文來源:http://29xue.comFor the sake of safety, the above rules must not be careless in the use of electric torque wrenches, we must take them seriously, after all, safety is the first. Source: http://29xue.com

上海11选5 上海11选5 上海11选5 江西11选5 江西11选5 江西11选5 3D之家 3D之家